Noorwegen
Vrij van rechten*
- Hun lijnen2 Noorse lijnen
87.08.9410 For the vehicles of heading 87.01
Noorse tariefgegevens gecontroleerd 13 september 2026.
Code 8708 94 · Post 8708
Officiële tarieftekst
Delen en toebehoren van motorvoertuigen bedoeld bij de posten 8701 tot en met 8705, andere delen en toebehoren, stuurwielen, stuurkolommen en stuurhuizen; delen daarvan
Kies de omschrijving die het beste bij je product past.
Invoerrechten op de codes hieronder: 3.5–4.5%*
4 codes hieronder
Probeer een korter woord, of zoek in plaats daarvan in het hele tarief.
Verkopen aan Noorwegen, Groot-Brittannië en de Verenigde Staten
Noorwegen, Groot-Brittannië en de Verenigde Staten hebben eigen tarieflijnen onder de HS-code van zes cijfers. De tarieven hieronder zijn wat hun douane heft op goederen die uit de EU aankomen. Leg de goederen naast de eigen omschrijving van elk land voordat je op een tarief vertrouwt.
Noorwegen
Vrij van rechten*
87.08.9410 For the vehicles of heading 87.01
Noorse tariefgegevens gecontroleerd 13 september 2026.
Groot-Brittannië
Van 0.0% tot 4.0%*
8708 94 20 00 For the industrial assembly of: Vehicles of heading|8703; Vehicles of heading|8704|with
Voor Noord-Ierland gelden andere regels.
Britse tariefgegevens gecontroleerd 13 september 2026.
Verenigde Staten
15.0%†
Geschat op basis van gepubliceerde Amerikaanse maatregelen
8708.94.10.00 Parts and accessories of the motor vehicles of headings 8701 to 8705, Other parts
De Amerikaanse importeur dient de aangifte in.
Amerikaanse tariefgegevens gecontroleerd 16 september 2026.
Noorwegen deelt de 6-cijferige categorie op zijn eigen manier in. Dit zijn dus de Noorse onderverdelingen binnen die categorie, niet deze EU-code. Vergelijk je product met hun omschrijving; per onderverdeling staat wat de Noorse douane heft.
87.08.9410
For the vehicles of heading 87.01
87.08.9490
Other
Bevat gegevens van de Noorse douane (data.toll.no), gelicentieerd onder CC BY 4.0, bewerkt voor weergave.
Wat de Britse douane heft wanneer zulke goederen in Groot-Brittannië aankomen.
8708 94 20 00
For the industrial assembly of: Vehicles of heading|8703; Vehicles of heading|8704|with either a compression-ignition internal combustion piston engine (diesel or semi-diesel) of a cylinder capacity not exceeding 2|500|cm$3|or with a spark-ignition internal combustion piston engine of a cylinder capacity not exceeding 2|800|cm$3; Vehicles of heading|8705
8708 94 35 00
Steering wheels, steering columns and steering boxes
8708 94 91 00
Of closed-die forged steel
8708 94 99 10
Hub gear made of cold rolled carbon steel (per ASTM A1008), molded into the plastic and pressed on pinion, with: -an outer diameter of 81,2 mm or more, but not more than 82,55 mm, -an inner diameter of 25,9 mm or more, but not more than 25,97 mm, -a height of the lower side of inner diameter of 11,63 mm or more, but not more than 12,13 mm, -a height of the upper side of inner diameter of 3,25 mm or more, but not more than 3,5 mm, -an overall height of 11,63 mm or more, but not more than 19,5 mm for use in the manufacture of vehicle's steering system
8708 94 99 20
Intermediate steering shaft forming part of the steering column with: -a torsional rigidity of 25 Nm/degree or more, -a tubular male shaft in welded carbon steel tube (per GB/T 699 grade 20), -a tubular female shaft in welded carbon steel tube (per with GB/T 699 grade 20), -two spiders universal joint made of chromium alloy steel (per GB/T 5216 grade 20CrMnTiH), -a length in nominal telescope position of 396 mm or more but not more than 467 mm, -a coupling interface on both ends with internal toothing, -two cardan joints on both sides, -a telescope shaft function with a range of 74 mm or more but not more than 115 mm, for use in the manufacture of vehicle's steering system
8708 94 99 30
Lower assist shaft as part of the steering column made of carbon steel (per GB/T699 grade 45 or JIS G4051 grade S45C) with: -an ultimate torsional strength load of 325 Nm or more and Johnson Apparent Elastic Limit (J.A.E.L) values of 275 Nm or more, -a length of 66,39 mm or more but not more than 88,64 mm, -an outer diameter of 27,47 mm or more but not more than 28,38 mm, -an inner hole of diameter 6,50 mm or more but not more than 6,58 mm, -an external 26-teeth spline with major diameter 21,18 mm or more but not more than 21,44 mm, -a knurling on a part of outer surface of major diameter 26,0 mm or more but not more than 26,1 mm, -with or without an external 24-tooth spline and with a major diameter 24,75 mm or more but not more than 25 mm, for use in the manufacture of vehicle's steering system
8708 94 99 40
Upper assist shaft as part of the steering column made of carbon steel (per GB/T699 grade 45) with: -an ultimate torsional strength load of 325 Nm or more and Johnson Apparent Elastic Limit (J.A.E.L) values of 275 Nm or more, -a length of 165,3 mm or more but not more than 204,2 mm, -an outer diameter of 22,87 mm or more but not more than 22,92 mm, -an internal hole of diameter 6,50 or more but not more than 6,58 mm, -an external spline, for use in the manufacture of vehicle's steering system
8708 94 99 50
Lower shaft as part of the steering column made of aluminium alloy (per ASTM B221M grade 6105), air quenched and tempered with: -an ultimate torsional strength of 260 Nm or more, -a length of 296,7 mm or more but not more than 297,8 mm, -an external 18-tooth spline on all shaft length with major diameter of 28,7 mm or more but not more than 29 mm, -an 18-tooth internal spline with a minor diameter of 19,7 mm or more but not more than 20 mm, for use in the manufacture of vehicle's steering system
8708 94 99 60
Torsion bar as part of the steering column made of carbon alloy steel (per SAE J1268, grade 5160H of modified chemistry for carbon content of 0,53 or more, but not more than 0,56) with: -a shaft torsional stiffness of 2,5 Nm/degree or more but not more than 2,7 Nm/degree, -a length of 107,75 mm or more but not more than 108,25 mm, -an outer diameter of 6,38 mm or more but not more than 6,42 mm, -two external 18-tooth splines on both shaft ends with a major diameter of 6,70 mm or more but not more than 6,85 mm, as interface to pressing with matting input and output shafts, -entire surface shot peened, for use in the manufacture of vehicle's steering system
8708 94 99 70
Tubular steering shaft as part of the steering column made of carbon steel welded tube (per EN 10305/2, E235 C or GB/T699 grade 20) with: -an ultimate torsional strength of 300 Nm or more and Johnson Apparent Elastic Limit (J.A.E.L) values of 275 Nm or more, -a length of 245,48 mm or more but not more than 287,5 mm, -an outer diameter of 23,95 mm or more but not more than 32,25 mm, -an interface for steering wheel connection either in a form of an external 40-tooth spline with major diameter of 17,1 mm or more but not more than 17,5 mm and an internal thread M12x1,75-6H or in a form of an external hexagon with a short diagonal of 15,05 mm or more but not more than 15,35mm and an internal thread M10x1.5-6H, -an interface either in a form of an internal 10-tooth spline of length of 98.0 mm or more but not more than 160 mm, with minor diameter of 16,1 mm or more but not more than 16,4 mm or in a form of an internal 48-tooth spline of length of 151 mm or more but not more than 160 mm, with minor diameter of 23,2 mm or more but not more than 23,3 mm, for use in the manufacture of vehicle's steering system
8708 94 99 80
Blank assembly worm gear, consisting of a hub of carbon steel (GB/T 699 grade 25 or DIN EN 10277 grade 11SMn30) and a ring of cast polyamide 6/12 with: - an outer diameter of 97,35 mm or more, but not more than 102,65 mm, - an inner diameter of 27,91 mm or more, but not more than 27,93 mm, - a height of the hub of 11,75 mm or more, but not more than 12,00 mm, - an overall height of 16,00 mm or more, but not more than 18,00 mm
8708 94 99 90
Other
Deze tarieven gelden in Groot-Brittannië. Voor goederen die Noord-Ierland binnenkomen, kunnen andere regels gelden.
Bevat overheidsinformatie die is gelicentieerd onder de Open Government Licence v3.0.
Bron: UK Department for Business and Trade (data.api.trade.gov.uk).
Wat de Amerikaanse douane heft wanneer goederen zoals deze uit de EU aankomen. De Amerikaanse importeur dient de aangifte in en betaalt de rechten.
8708.94.10.00
Parts and accessories of the motor vehicles of headings 8701 to 8705, Other parts and accessories, Steering wheels, steering columns and steering boxes; parts thereof, Steering wheels, steering columns and steering boxes, For tractors suitable for agricultural use
8708.94.50.00
Parts and accessories of the motor vehicles of headings 8701 to 8705, Other parts and accessories, Steering wheels, steering columns and steering boxes; parts thereof, Steering wheels, steering columns and steering boxes, For other vehicles
8708.94.60.00
Parts and accessories of the motor vehicles of headings 8701 to 8705, Other parts and accessories, Steering wheels, steering columns and steering boxes; parts thereof, Parts, For tractors suitable for agricultural use
8708.94.65.00
Parts and accessories of the motor vehicles of headings 8701 to 8705, Other parts and accessories, Steering wheels, steering columns and steering boxes; parts thereof, Parts, For other tractors (except road tractors)
8708.94.70.00
Parts and accessories of the motor vehicles of headings 8701 to 8705, Other parts and accessories, Steering wheels, steering columns and steering boxes; parts thereof, Parts, For other vehicles, Of cast iron
8708.94.75.10
Parts and accessories of the motor vehicles of headings 8701 to 8705, Other parts and accessories, Steering wheels, steering columns and steering boxes; parts thereof, Parts, For other vehicles, Other, Steering shaft assemblies incorporating universal joints
8708.94.75.50
Parts and accessories of the motor vehicles of headings 8701 to 8705, Other parts and accessories, Steering wheels, steering columns and steering boxes; parts thereof, Parts, For other vehicles, Other
Antidumpingrechten, compenserende rechten, Amerikaanse invoerbelastingen en douanekosten zijn niet inbegrepen.
De beschrijvingen hierboven zijn de Amerikaanse tariefteksten, die de Verenigde Staten alleen in het Engels publiceert.
Bron: de Harmonized Tariff Schedule van de US International Trade Commission (hts.usitc.gov), publiek domein, en de maatregelen die zijn gepubliceerd in het Federal Register.
Dit is een planningsschatting op basis van de Amerikaanse Harmonized Tariff Schedule (de getoonde revisie) en de maatregelen die op de getoonde datum zijn gepubliceerd in het Federal Register, voor een zending met oorsprong in de EU. Het is geen douaneaangifte, juridisch advies of het oordeel van een expediteur, en douanecodes.nl is geen Amerikaans erkende douane-expediteur. De Amerikaanse importeur of diens expediteur bevestigt de indeling, de oorsprong, de waarde en de verschuldigde rechten voordat er aangifte wordt gedaan.
De hier getoonde tarieven zijn schattingen, gelezen uit officiële tariefgegevens van de EU, Noorwegen en het Verenigd Koninkrijk, alleen ter oriëntatie. Controleer het actuele tarief in het Gebruikstarief van de Nederlandse Douane, in TARIC, bij de Noorse douane of in de Britse Online Trade Tariff voordat je aangifte doet. Het tarief dat je betaalt, kan ook afhangen van het land van oorsprong. Dit zijn alleen de basisinvoerrechten: invoer-btw, accijnzen, antidumpingrechten en vrijwarings- of contingentmaatregelen zitten er niet in.
Maak een gratis account aan om de goederencodes die je nodig hebt op één plek te bewaren en ze terug te vinden wanneer je ze nodig hebt.